Hi-Scan Pro Operation Guide 1.pdf

(8609 KB) Pobierz
OPERATION GUIDE
PROLOGUE
CAUTION : Any changes or modifications in construction
of this device which is not expressly approved by the
party Responsible for compliance could void the user’s
authority to operate the equipment.
NOTE : This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. The limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
OPERATION GUIDE
2
PROLOGUE
TABLE of CONTENTS
SAFETY
UNPACKING
I. GENERAL INFORMATION
1. GENERAL FEATURES………………………………………I-2
2. SPECIFICATIONS……………………………………………I-4
3. FUNCTION CONFIGURATION…………………………….I-6
4. PARTS DESCRIPTION………………………………………I-7
II. INTRODUCING Hi-Scan Pro
1. PROGRAM LEVEL CONFIGURATION……………………..II-2
2. OPERATION PRINCIPLE…………………………………….II-5
3. COMPOSITION OF MENU SCREEN……………………….II-11
4. MESSAGE DISPLAY………………………………………….II-12
5. POWER SUPPLY………………………………………………II-13
6. INTERNAL BATTERY CHARGING…………………………II-16
7. POWER ON/OFF OPERATION……………………………..II-17
8. TOP MENU LEVEL OPERATION……………………………II-18
9. INIT LEVER OPERATION……………………………………II-21
10. MENU LEVEL OPERATION………………………………….II-25
11. MODE LEVEL OPERATION………………………………….II-27
III. VEHICLE SCOPEMETER
1. CONNECTION METHOD………………………………III-2
2. ENGINE…………………………………………………..III-4
3. AUTOMATIC TRANSAXLE…………………………….III-12
4. ABS……………………………………………………….III-13
5. OSCILLOSCOPE…………………………………………III-14
6. METER(V, F, R, A, T, P)………………………………..III-21
7. ACTUATOR DRIVING…………………………………..III-27
8. SENSOR SIMULATOR…………………………………..III-30
OPERATION GUIDE
3
PROLOGUE
IV. CARB OBD-II DIAGNOSIS
1. CONNECTION METHOD…………………………………….IV-2
2. COMMUNICATION INTERFACE…………………………….IV-4
3. READINESS TEST……………………………………………..IV-7
4, CURRENT DATA………………………………………………IV-10
5. DIAGNOSTIC TROUBLE CODES…………………………….IV-14
6. FREEZE FRAME DATA………………………………………..IV-17
7. EXPANDED DIAG. PROTOCOL……………………………..IV-20
8. 02 TEST RESULTS…………………………………………….IV-27
9. MONITORING TEST RESULTS……………………………….IV-30
10. COMBINATION DISPLAY……………………………………IV-33
11. ECU INFORMATION………………………………………….IV-37
12. PENDING ECU…………………………………………………IV-38
V. FLIGHT RECORD REVIEW
VI. SYSTEM SETUP
1. CONNECTION METHOD……………………………..VI-2
2. SYSTEM CONFIGURATION…………………………..VI-4
3. DATA SETUP……………………………………………VI-9
4. PRINTER SETUP………………………………………..VI-12
5. SYSTEM TEST…………………………………………..VI-14
6. METER ZERO SET………………………………………VI-16
VII. USER
1.
2.
3.
4.
5.
6.
7.
8.
MAINTENANCE
SOFTWARE CARD INSTALL…………………………VII-2
MEMORY CARD INSTALL……………………………VII-3
RUBBER SHROUD COVERING……………………….VII-4
FUSE REPLACEMENT………………………………….VII-5
PRINTER PAPER CHANGE……………………………VII-6
REPLACING BATTERY………………………………..VII-7
CHARGING BATTERY…………………………………VII-8
FINISHING UP………………………………………….VII-9
APPENDIX
A. IMPORTANT MESSAGE DESCRIPTION
B. KEY SYMBOL MEANING
OPERATION GUIDE
4
PROLOGUE
SAFETY
Safety Precautions
This equipment described in this manual is intended for use only
by qualified personnel. Safe and effective use of this equipment is
dependent upon the operator following normally accepted safety
practices and procedures in conjunction with the special
requirements detailed in this manual. Specific warning and cautionary
statements will be found, where applicable, throughout this manual.
Where necessary, the WARNING statements and ICON will be
described this guide.
WARNING identifies conditions or actions which may damage Hi-
Scan Pro or the vehicle.
OPERATION GUIDE
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin