GSM/GPRS/GPS TRACKER
MANUAL
UPreface
Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual. Any change will be integrated in the latest release. The manufacturer assumes no responsibility for any errors or omissions in this document.
Contents
1. Summary 3
2. Application 3
3 Usage 3
3.1 SIM card installation 3
3.2 Battery and Charger 3
3.3. Startup 3
4 Device Parameter Settings 4
4.1 Initialization 4
4.2 Set password 4
4.3 Authorization 5
4.4 Mode switch between GPS and LBS 5
4.5 Single Locating 5
4.6 Voice Surveillance 5
4.7 Geo-fence 5
4.8 Vibration alarm 6
4.9 SOS alarm 6
4.10 GPRS setting 6
4.11 Check device setting 7
4.12 Device restart 7
Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or internet. Device is transmitting data by inspecting vibration of device.
l Protect child / the old / the disabled / pet etc
l Provide peace-of-mind for businessmen
l Personnel Management
l Criminals Tracking
3.1 SIM card installation
Make sure that there is no call transfer and call display is on, and PIN code off. The SMS message must in Text format, can’t be identified for PDU format.
3.2 Battery and Charger
Do charge the battery to capacity in 8 -12 hours for first time. Please use the battery and charger provided by the manufacturer. This unit adopts built-in Li-ion battery, and full battery can standby 48 hours. After first use, the battery usually should be charged fully in 10 hours.
3.3. Startup
l Put the SIM card in SIM card slot, device will start automatically, red light keep stable lighting, device light turns off and enter into power-saving mode after 5 minutes.
l In 10 - 40 seconds, the unit will begin to work and acquire the GSM signal as well as the GPS signal and start normal working.
l Device has GPS and LBS two working mode, when in GPS mode, device must be put open outside.
l For first use, please initialize the unit and restore it to default setting.
l When device can work normally, you can use it and do any setting as the instructions of this manual.
4.1 Initialization
Send SMS “SBCZ” to the tracker, it will reply “RESET OK” and initialize all the settings. (Default password: 000000).
Remark: initialization is resetting all the parameters to factory defaults.
4.2 Set password
4.2.1Set Password: Send SMS: “#mm#old password#new password#” to the unit to change the password.
For Example, send SMS: “#mm#000000#123456#” to device, it will reply SMS: “MM OK”.
4.2.2 Make sure the new password is in 6 digits arabic numbers, or the device cannot recognize the password.
4.3 Authorization
Please set authorization number before using, it has 2 numbers can be set.
4.3.1 Send SMS “#BD#1#000000#number#” to set up first authorized number; send SMS “#BD#2#000000#number#” to set up second
authorized number device will reply “BD OK”.
4.4 Mode switch between GPS and LBS
4.4.1 Send SMS“#DW1#”, device will switch to GPS mode.
4.4.2 Send SMS “#DW2#”, device will switch to LBS mode.
4.5 Single Locating
4.5.2Send SMS“123” (LBS mode), it will reply address: around 118m, jianhui rd, bao’an district, Shenzhen, China.
4.5.3 Send SMS“321” (GPS mode), it will reply a real-time
Google link message as below:
https://maps.google.com/maps?q=N22.669973,E114.011467
4.6 Voice Surveillance
Dialing device number, device will get though and enter into voice listening mode.
4.7 Geo-fence
4.7.1 Set up: When the unit stays immobile in a place, send SMS ...
mimi31