MR415LAGUNA2(3).pdf

(5114 KB) Pobierz
2
Transmission
20A
CLUTCH
MANUAL GEARBOX
AUTOMATIC GEARBOX
DRIVESHAFTS
21A
23A
29A
X91
AUGUST 2009
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the manufacturer in
the production of the various component units and accessories from which the vehicles are
constructed".
All rights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part reference
numbering system is forbidden without the prior written authority of Renault.
EDITION ANGLAISE
© Renault s.a.s 2007
LAGUNA III - Section 2 ContentsPages
LAGUNA III - Section 2
Contents
Pages
20A
CLUTCH
Clutch: Precautions for the
repair
Clutch: Specifications
Pressure plate - Disc:
Removal - Refitting
Clutch thrust bearing:
Removal - Refitting
23A
AUTOMATIC GEARBOX
Automatic gearbox:
Specifications
Automatic gearbox: Parts
and consumables for the
repair
Automatic gearbox: List and
location of components
Automatic gearbox: Removal
- Refitting
20A-1
20A-2
20A-4
20A-11
23A-3
23A-4
23A-5
23A-6
23A-28
23A-29
23A-35
23A-50
23A-67
23A-82
23A-86
23A-88
23A-90
23A-91
21A
MANUAL GEARBOX
Manual gearbox oil:
Specifications
Manual gearbox oils:
Draining - Filling
Differential output seal:
Removal - Refitting
Manual gearbox: Removal -
Refitting
Input shaft lip seal: Removal
- Refitting
Automatic gearbox oil:
Specifications
21A-1
21A-2
21A-6
21A-14
21A-55
Automatic gearbox oil:
Draining - Filling
Hydraulic distributor:
Removal - Refitting
Hydraulic distributor wiring:
Removal - Refitting
Hydraulic distributor internal
wiring: Removal - Refitting
Gearbox oil cooler: Removal
- Refitting
Differential output seal:
Removal - Refitting
23A
AUTOMATIC GEARBOX
Automatic gearbox:
Precautions for the repair
Automatic gearbox:
Identification
Multifunction switch:
Removal - Refitting
23A-1
23A-2
Multifunction switch:
Adjustment
Speed sensor: Removal -
Refitting
Contents
23A
AUTOMATIC GEARBOX
Oil pressure switch: Removal
- Refitting
Automatic gearbox
converter: Removal -
Refitting
Converter seal: Removal -
Refitting
Automatic gearbox
converter: Removal -
Refitting
23A-93
23A-106
23A-107
23A-110
29A
DRIVESHAFTS
Front left-hand driveshaft:
Removal - Refitting
Front right-hand driveshaft:
Removal - Refitting
Relay shaft bearing:
Removal - Refitting
Front driveshaft gaiter, wheel
side: Removal - Refitting
Front right-hand driveshaft
gaiter, gearbox side:
Removal - Refitting
Front left-hand driveshaft
gaiter, gearbox side:
Removal - Refitting
29A-1
29A-7
29A-14
29A-17
29A-21
29A-26
CLUTCH
Clutch: Precautions for the repair
Special tooling required
Emb. 1780
Set of clutch plate centring
mandrels.
20A
Before removing the clutch, check:
- The direction of fitting for the clutch plate.
Before refitting the clutch, check:
- The flywheel friction track (no scratches or blue
stains),
- The crankshaft bearing (no sticking),
- The engine and gearbox seals (replace if necessary),
- The sliding action of the clutch plate on the output
shaft,
- The thrust bearing guide and the clutch fork (no wear
or scratches).
WARNING
To prevent the clutch from juddering or slipping, do
not grease the output shaft or the clutch plate hub.
During refitting:
Check the direction of the clutch plate.
Centre the clutch plate using the tool
(Emb. 1780)
Gradually torque tighten the clutch pressure plate
bolts.
After refitting, check:
- The clutch play (for a cable operated vehicle),
- Bleeding of the hydraulic circuit (for vehicles with hy-
draulic controls).
20A-1
CLUTCH
Clutch: Specifications
TL4
Pressure plate
20A
123819
Drive plate
123820
Number of splines:
21
Plate thickness:
6.9 mm
Plate outer diameter:
225 mm
20A-2

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin