Getting started - EDiTH with Windows Vista and 7.pdf

(342 KB) Pobierz
Using EDiTH with Windows Vista / 7
Feb. 2010
Step 1
-Using your internet browser of
choice, navigate to:
http://www.espar.com/tech_manuals/Diagn
ostic Software/
-‘Click’ on the most current version
of the EDiTH software
-Follow the prompts that appear in
order to download the software
Step 2
-Once the download has completed, navigate to
the location where the download was saved.
-‘Click’ on the setup file
-follow the on screen prompts for EULA, saving
location and confirmation of installation
-Windows Security will prompt several times
during installation asking for permission to install
the software. Click ‘Allow’.
Step 3
-Open the start menu and launch EDiTH
Step 4
-Minimize the EDiTH screen
-If using a Serial to USB convertor plug it into the
computer now(don’t connect the cable to the ISO adapter
yet)
-Windows Vista / 7 should recognize the Serial to USB
adapter and automatically install the required driver. If
you receive a message stating that the driver was
unsuccessfully installed please see the troubleshooting
section at the end of this tutorial.
-Unplug the adapter.
Step 5
-Maximize the EDiTH screen
-‘Click’ Ok on the EDiTH flash screen
- You may be prompted to make a COMM port
selection, just pick one it doesn’t matter at this point.
- Make a mental note as to which ports are displayed (COM3, in this case)
Step 6
-Plug the Serial to USB interface back into the
computer.
-You may see the messages from step 4 again this is
normal
-At the top of the screen there is a menu option called
“Options”, ‘Click’ it. Then select Serial Interface.
-You should now see another option for available COMM ports (COMM 8 in this
case). Highlight it and select ‘OK’.
-Close EDiTH
Step 7
-Download the EDiTH database update (03-2009)
http://www.espar.com/tech_manuals/Diagnostic%20Software/EDiTH%20database%20update%2003-2009.zip
-Navigate to download folder and select the file “Extract and run”
Step 8
-Navigate to Control Panel > Hardware and
sound > Power options ‘Click’ on the text
“Change plan settings”.
-‘Click’ on the text “Change advanced power
settings”
- Ensure that the ‘USB selective Suspend’ is
disabled by clicking on the highlighted text
Step 9
-Plug the Serial to USB cable into the ISO adapter
-Connect the ISO adapter to the Heater to be worked on
Step 10
-At the top of the screen under the “Heater” menu is an option for “Select
Heater”, ‘Click’ it.
-In most cases it is best to use the
“Automatic d..” option (Automatic
Detection)
-‘Click’ Yes.
Step 11
-In the example to the right
there are three possible tests
that can be performed.
-General data
-Used to obtain heater hours, codes and other
info (Heater does not turn on)
-Functional check
-Used to run the heater in real time, with
observable feedback of various sensors within
heater
-Switch on component
-Used to switch on individual components to test there operation
Troubleshooting
-
During Installation I received a message stating driver was unsuccessfully
installed
Plug the Serial to USB adapter into the computer without the ISO adapter attached
Navigate to Device Manager
Control Panel > Hardware and Sound – Under the Devices and Printers title select
“Device Manager”
-Select the view menu and
place a mark beside the ‘Show hidden
devices’ option
-Is there any Icons in the section marked
‘Ports’ with a yellow ‘!’ mark beside
them. If there is, the driver for that device
needs to be updated. Most Serial to USB adapters can operate on the driver
located at this link:
http://www.prolific.com.tw/support/files/%5CIO%20Cable%5CPL-2303%5CDrivers%20-
%20Generic%5CWindows%5Callinone%5CPL2303_Prolific_DriverInstaller_v110.zip
-
-If you are using the adapter that came with ISO adapter (sold through Espar) you
can find the updated driver at:
www.moxa.com/drivers/uport/u1130/V1.6/driv_win_uport1p_v1.6_build_090629
13_whql.zip
-Follow the steps when prompted to install the driver.
-Unplug the Serial to USB adapter
-Reboot computer
-Plug Serial to USB adapter back into computer
-Navigate to Device manager again
-Ensure that the Computer has
recognized the adapter and does not
have a error (error will be indicated by
the presence of a yellow ‘!’ beside the
device)
-Continue with normal installation of EDiTH
When I plug the Serial to USB device into the computer I don’t get another
COMM port.
-Did the driver install properly?
Navigate to Device Manager and ensure there are no “!” marks beside any
of the items listed under ‘Ports (COM &LPT)’
-Follow the steps from the previous section to ensure driver for Serial to USB
installed correctly.
I am having another problem that is not listed here.
-If the issue is in regards to the EDiTH software package
Please contact Espar’s Technical Dept at 1-800-387-4800
-If the issue is in regards to the Serial to USB adapter or Windows 7
Please contact your computer specialist or system administrator.
-

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin