2007-Current-quick-reference-maint-storage.pdf

(16660 KB) Pobierz
R
Quick Reference Guide
Tips for Proper Maintenance and Storage of your GEM
2007-Current
GEM e2, GEM e4, GEM e6®, GEM eS, GEM eL, GEM eL XD
BaSic vEhicLE oPERaTion inSTRucTionS:
• Disconnect the Charging Cord from the vehicle before operating
• Master Disconnect Switch must be in the ON position
• Turn key clockwise to the ON position
• The display will indicate an illuminated red colored Brake Light
symbol in the upper left corner, fully release the Parking Brake Lever
• Select driving mode (R, DL, or DH)
• Press Accelerator Pedal and go
SERvicE coDES
(The Service Code is displayed in the same location as the
mph/kph and is accompanied by the Service Wrench icon.)
[06]
Indicates that the Accelerator Pedal is pressed and no
direction has been selected.
Release accelerator Pedal and
insure Direction Switch is locked into position.
[11]
Indicates Accelerator Pedal is pressed before key is turned
to the ON position.
Turn key to OFF position. Release
Accelerator Pedal. Turn key to ON position.
[15]
Indicates a low state of charge for the batteries.
Fully
charge batteries before operating.
[16]
Indicates that there is a high state of charge for the
batteries.
Turn headlights on for several minutes, then turn
key switch to the OFF position and then to the ON position.
Master Disconnect Switch
* If you see other Service Indication Codes please contact your dealer for service. A
complete list of error codes is available in the Service Manual, a purchasable item
from your local authorized GEM dealer.
Please refer to your Owner’s Manual for more detailed information regarding your vehicle.
HOW TO DETERMINE IF CHARGE IS AT 100%
After charging is 100% complete, the Charger Connected icon will be the only thing
lit and the bar graph will not be illuminated. A green light on the charger itself will
also illuminate when the car is 100% charged. To know if the charging process is
complete, all ten bars on the State of Charge Indicator should be illuminated when
the car is turned on. If neither the Charger Connected icon nor the State of Charge
Indicators are illuminated, the charger may not be charging. If this occurs, make sure
the Main Disconnect Switch is in the ON position. More information on the charger
and charging of the batteries is discussed on pages 76-81 of the Owner’s Manual.
Plugged In Charging
Charge Complete
PERcEnT oF chaRGE DiSPLaY
The new charging display on the 2010 GEM car model years, makes it easy for the
GEM user to tell how much battery life is available. When the vehicle is plugged in
and charging, the percent of charge is displayed.
30% Charged
74% Charged
99% Charged
Please refer to your Owner’s Manual for more detailed information regarding your vehicle.
BATTERY CHARGING
on the bed of the GEM eS, GEM eL, GEM eL XD, and the GEM e6 models, or under
the maintenance plate on the rear spat of the GEM e2, GEM e4, and GEM e6 models,
bench seat, with the remaining three located under the access panel located on the
pedestal, with access through the panel located on the front of that pedestal. More
under the access panel on either the rear bed or rear spat. The charging system is
life and performance out of your GEM. Because of high power draw at low states of
REchaRGE vEhicLE aFTER Each uSE.
Your GEM is equipped with a battery charger that includes a feature that will monitor
the state of charge of the batteries, and will initiate a charge cycle whenever the
batteries fall to a pre-determined charge level. To enable this feature, leave the
Master Disconnect Switch in the ON position (see figure A on previous page) and keep
your car plugged into a standard household 15-amp 110/120-volt A/C outlet. Charger
also works on a 20-amp 220/240-volt A/C outlet.
NOTE: THE BATTERIES USED IN YOUR GEM WILL PERFORM BETTER WHEN kEPT
FULLY CHARGED. THEREFORE, WHENEVER POSSIBLE, RECHARGE THE BATTERIES—NO
MATTER WHAT STATE OF CHARGE IS INDICATED.
1. The Master Disconnect Switch must be in the ON position for the charger to operate
and charge the batteries. The Master Disconnect Switch is located in the Fuse Access
Panel of the white lower dash.
2. The Battery Charger Receptacle
is located on the hood. It accepts a
standard, 3-wire, grounded extension
cord. The extension cord should not
exceed the following: 12-gauge wire 50
feet in length or 14-gauge wire 25 feet
in length.
3. Insert the proper extension cord into
the Battery Charger Receptacle.
4. Plug the extension cord into a 110-
volt A/C, 15-amp breaker outlet. A
Ground Fault interrupt protected circuit
(GFI) is recommended. To EnSuRE
PROPER CHARGING, NO OTHER CARS, APPLIANCES, DOOR OPENERS, ETC. CAN BE
PLUGGED INTO THE SAME CIRCUIT. DO NOT USE A GFCI CORD WITH A GFCI OUTLET.
5. A full recharge cycle can take from 8 to 14 hours (if the state of charge indicator is
indicating only one red bar), depending on battery option-12 volt or 8 volt.
Please refer to your Owner’s Manual for more detailed information regarding your vehicle.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin